The 034B, manufactured by Met One, combines a three-cup anemometer and vane into a single integrated package to measure wind speed and direction. It is cabled for use with our data loggers, and it can provide you with measurements for a variety of applications.Read More
The 034B monitors wind speed using a three-cup anemometer that contains a sealed magnetic reed switch. Rotation of the cup wheel produces a pulse that is directly proportional to wind speed. The frequency of the pulse is measured by the data logger pulse count channel, then converted to engineering units (mph, m/s, knots).
Wind direction is sensed with a potentiometer. With the precision excitation voltage from the data logger applied to the potentiometer element, the output signal is an analog voltage that is directly proportional to the azimuth of the wind direction.
|Applications||General (Rain with light snow. Little or now riming or blowing sand. No salt spray.)|
|Sensor||3-cup anemometer and vane|
|Measurement Description||Wind speed and direction|
|Operating Temperature Range||-30° to +70°C|
|Weight||907 g (2.0 lb)|
Wind Speed (Anemometer)
|Range||0 to 75 m/s (0 to 167 mph)|
|Starting Threshold||0.4 m/s (0.9 mph)|
|Sensor Output||Pulsed contact closure|
|Resolution||(0.7998 m s–1) / (scan rate in seconds) or (1.789 mph) / (scan rate in seconds)|
|Anemometer Radius||10.7 cm (4.2 in.)|
|Anemometer Height||24.4 cm (9.6 in.)|
|Output Signal||Contact closure (reed switch)|
Wind Direction (Vane)
|Electrical Range||356° (4° open)|
|Potentiometer Resistance||0 to 10 kΩ (open at crossover)|
|Threshold||0.4 m s–1 (0.9 mph)|
|Vane Length||33.5 cm (13.2 in.)|
Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.
|CR500 (retired)||Measurements are typically processed for output with the Wind Vector instruction, which is not present in the CR500.|
|CR9000 (retired)||*Measurements are typically processed for output with the Wind Vector instruction, which is not present in the CR9000.|
The 034B can be attached to a Campbell Scientific crossarm using a 17953 Nu-Rail fitting or a CM220 Right Angle Mounting Bracket. Alternatively, the 034B can be attached to the top of our stainless-steel tripods via the CM216 Sensor Mounting Kit. The CM216 extends 4 inches above the mast of a CM106B, CM110, CM115, or CM120 tripod.
The 034B's anemometer uses one pulse count channel on the data logger. Its wind vane requires one single-ended channel and access to an excitation channel (the excitation channel can be shared with other high impedance sensors).
The 034B's anemometer is measured by the PulseCount Instruction in CRBasic, and by Instruction 3 (Pulse Count) in Edlog. The wind vane is measured by the BrHalf Instruction in CRBasic and by Instruction 4 (Excite-Delay-SE) in Edlog. The measurements are typically processed for output with the Wind Vector instruction (not present in the CR500 or CR9000).
Number of FAQs related to 034B-L: 15
Expand AllCollapse All
Wind vane tails are user-replaceable and are available for purchase as pn 13765, Replacement Wind Vane Tail for 034B or 034A.
No. A data logger is needed to measure and store data from the 034B-L.
For proper siting of the wind sensor, refer to the 034B-L manual. The 034B-L can be mounted using a 1.00 IPS pipe of any length.
The supply voltage is 5 Vdc.
They are completely interchangeable, and no changes are needed.
The 034B-L uses a switch closure for wind speed measurement, and the 03002-L uses a low-level ac output for wind speed measurement. Both use a pulse channel on the data logger to measure wind speed.
The sensor does not consume power to operate.
The information included on a calibration sheet differs with each sensor. For some sensors, the sheet contains coefficients necessary to program a data logger. For other sensors, the calibration sheet is a pass/fail report.
Most Campbell Scientific sensors are available as an –L, which indicates a user-specified cable length. If a sensor is listed as an –LX model (where “X” is some other character), that sensor’s cable has a user-specified length, but it terminates with a specific connector for a unique system:
If a sensor does not have an –L or other –LX designation after the main model number, the sensor has a set cable length. The cable length is listed at the end of the Description field in the product’s Ordering information. For example, the 034B-ET model has a description of “Met One Wind Set for ET Station, 67 inch Cable.” Products with a set cable length terminate, as a default, with pigtails.
If a cable terminates with a special connector for a unique system, the end of the model number designates which system. For example, the 034B-ET model designates the sensor as a 034B for an ET107 system.
Not every sensor has different cable termination options. The options available for a particular sensor can be checked by looking in two places in the Ordering information area of the sensor product page:
If a sensor is offered in an –ET, –ETM, –LC, –LQ, or –QD version, that option’s availability is reflected in the sensor model number. For example, the 034B is offered as the 034B-ET, 034B-ETM, 034B-LC, 034B-LQ, and 034B-QD.
All of the other cable termination options, if available, are listed on the Ordering information area of the sensor product page under “Cable Termination Options.” For example, the 034B-L Wind Set is offered with the –CWS, –PT, and –PW options, as shown in the Ordering information area of the 034B-L product page.
Note: As newer products are added to our inventory, typically, we will list multiple cable termination options under a single sensor model rather than creating multiple model numbers. For example, the HC2S3-L has a –C cable termination option for connecting it to a CS110 instead of offering an HC2S3-LC model.