The 03002, manufactured by R. M. Young, measures wind speed and direction with a three-cup anemometer and a wind vane mounted on a small crossarm. It interfaces directly with your Campbell Scientific data loggers, so no signal conditioning is required.Read More
|Applications||General (Rain with light snow. Little or no riming or blowing sand. No salt spray.)|
|Sensor||3-cup anemometer and vane|
|Measurement Description||Wind speed and direction|
|Operating Temperature Range||-50° to +50°C (assuming non-riming conditions)|
|Height||32 cm (12.6 in.)|
|Crossarm Length||40 cm (15.7 in.) between instruments (center-to-center)|
|Mounting Diameter||34 mm (1.34 in.); mounts on standard 1-in. IPS pipe|
Wind Speed (Anemometer)
|Range||0 to 50 m/s (0 to 112 mph)|
|Gust Survival||60 m/s (134 mph)|
|Sensor||12-cm diameter cup wheel assembly, 40-mm diameter hemispherical cups|
|Accuracy||±0.5 m/s (1.1 mph)|
|Turning Factor||75 cm (2.5 ft )|
|Distance Constant||2.3 m (7.5 ft) 63% recovery|
|Starting Threshold||0.5 m/s (1.1 mph)|
|Transducer||Stationary coil (1300 ohm nominal resistance)|
|Transducer Output||AC sine-wave signal induced by rotating magnet on cup wheel shaft 100 mV peak-to-peak at 60 rpm (6 V peak-to-peak at 3600 rpm)|
|Output Frequency||1 cycle per cup wheel revolution (0.75 m/s per Hz)|
|Cup Wheel Diameter||12 cm (4.7 in.)|
|Weight||113 g (4 oz)|
Wind Direction (Vane)
|Electrical Range||352° (8° open)|
|Settling Time||20 ms|
|Sensor||Balanced vane; 16 cm turning radius|
|Delay Distance||0.5 m (1.6 ft) 50% recovery|
|Transducer Excitation||Requires regulated dc voltage. (15 Vdc maximum)|
|Transducer Output||Analog dc voltage proportional to wind direction angle with regulated excitation voltage supplied by the data logger|
|Vane Length||22 cm (8.7 in.)|
|Weight||170 g (6 oz)|
Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.
The 03002 is supplied with a 12-in.-long x 1-in. IPS unthreaded aluminum pipe, which mounts to a crossarm via a CM220 Mount or 17953 Nu-Rail fitting. The 03002 can also be mounted to the top of a CM106B or stainless-steel tripod via the CM216.
An ideal application for the Wind Sentry is wind profile studies. For this application, the LLAC4 4-channel Low Level AC Conversion Module can be used to increase the number of anemometers measured by one data logger. The LLAC4 allows data logger control ports to read the anemometer’s ac signals instead of using pulse channels. Data loggers compatible with the LLAC4 are the CR200(X)-series (ac signal ≤1 kHz only), CR800, CR850, CR1000, CR3000, and CR5000.
The anemometer is measured by the PulseCount instruction in CRBasic, and by Instruction 3 (Pulse Count) in Edlog. The wind vane is measured by the BrHalf Instruction in CRBasic, and by Instruction 4 (Excite-Delay-SE) in Edlog. The measurements are typically processed for output with the Wind Vector Instruction (not present in the CR500 or CR9000).
Number of FAQs related to 03002-L: 9
Expand AllCollapse All
It is possible, but Campbell Scientific does not recommend user replacement. Factory replacement is strongly recommended.
A CM202, CM204, or CM206 crossarm can be used. Select the appropriate crossarm for the application. To mount the sensor to the crossarm, use a CM220 (Right-Angle Mounting Bracket) or a 17953 (1- x 1-inch NU-RAIL Crossover Fitting). To mount the sensor to the top of a CM110-series tripod, use a CM216 (Apex Sensor Mount for SS Tripod).
One cup cannot be replaced at a time. The whole cup assembly would need to be replaced. The cup assembly can be replaced by the user.
The 034B-L uses a switch closure for wind speed measurement, and the 03002-L uses a low-level ac output for wind speed measurement. Both use a pulse channel on the data logger to measure wind speed.
Most Campbell Scientific sensors are available as an –L, which indicates a user-specified cable length. If a sensor is listed as an –LX model (where “X” is some other character), that sensor’s cable has a user-specified length, but it terminates with a specific connector for a unique system:
If a sensor does not have an –L or other –LX designation after the main model number, the sensor has a set cable length. The cable length is listed at the end of the Description field in the product’s Ordering information. For example, the 034B-ET model has a description of “Met One Wind Set for ET Station, 67 inch Cable.” Products with a set cable length terminate, as a default, with pigtails.
If a cable terminates with a special connector for a unique system, the end of the model number designates which system. For example, the 034B-ET model designates the sensor as a 034B for an ET107 system.
Not every sensor has different cable termination options. The options available for a particular sensor can be checked by looking in two places in the Ordering information area of the sensor product page:
If a sensor is offered in an –ET, –ETM, –LC, –LQ, or –QD version, that option’s availability is reflected in the sensor model number. For example, the 034B is offered as the 034B-ET, 034B-ETM, 034B-LC, 034B-LQ, and 034B-QD.
All of the other cable termination options, if available, are listed on the Ordering information area of the sensor product page under “Cable Termination Options.” For example, the 034B-L Wind Set is offered with the –CWS, –PT, and –PW options, as shown in the Ordering information area of the 034B-L product page.
Note: As newer products are added to our inventory, typically, we will list multiple cable termination options under a single sensor model rather than creating multiple model numbers. For example, the HC2S3-L has a –C cable termination option for connecting it to a CS110 instead of offering an HC2S3-LC model.
Many Campbell Scientific sensors are available with different cable termination options. These options include the following:
Note: The availability of cable termination options varies by sensor. For example, sensors may have none, two, or several options to choose from. If a desired option is not listed for a specific sensor, contact Campbell Scientific for assistance.
To incorporate a sensor that is compatible with wireless sensor interfaces into a wireless network, a CWS900-series wireless sensor interface is needed, as well as an A205 CWS-to-PC interface to configure it.