CSAT3BH
 
CSAT3BH Heated 3-D Sonic Anemometer with Integrated Electronics
 

Add to your Quote List


Common Accessories

CSAT3HCBL1-L
 
The CSAT3HCBL1-L provides communication between the data logger and the CSAT3H Controller Box via RS-485. The -L denotes the user-defined length of the cable between 1 and 300 feet (0.3 and 91.44 m).
CSAT3HCBL2
 
The CSAT3HCBL2 is a 4.57 m (15 ft) cable that provides communication between a PC and a CSAT3H Controller Box via RS-485.

Note: You do not need the CSAT3HCBL2 to communicate with the controller box via a data logger. For this type of communication connection, use a CSAT3HCBL1-L instead.
CSAT3HCBL3-L
 
One CSAT3HCBL3-L is needed per CSAT3BH. The CSAT3HCBL3-L is used to provide a 24 Vdc power source to the CSAT3H Controller Box. The -L denotes the user-defined length of the cable between 1 and 30 feet (0.3 and 9.14 m).
L10080
 
The 10080 is a thermocouple cover for the FW05 connector.
FW05
 
Measures atmospheric temperature gradients or fluctuations with research-grade accuracy.
FW/ENC
 
Protects thermocouples during shipping and transport.
FWC-L
 
FWC-L Connector Cable for Fine Wire TCs
 
Connects a fine-wire thermocouple to a data logger.
CS106
 
The CS106 measures barometric pressure for the range of 500 to 1100 hPa (mBar). This range equates to from below sea level (as in a mine) to over 15,000 feet above sea level.
HYGROVUE10
 
HYGROVUE10 Digital Temperature and Relative Humidity Sensor with M12 Connector
 
The HygroVUE™10 offers a combined temperature and relative humidity element in an advanced digital sensor that is ideal for weather networks. The electronics within the sensor provide accurate measurements, and the sensor is easy to use. The digital SDI-12 output allows a simple connection and measurement by many data logging systems. Another benefit is that this digital output avoids the extra errors associated with measuring analog sensors.
Cable Length Options
-10 -10 w/10ft per sensor
-17 -17 w/17ft per sensor
-33 -33 w/33ft per sensor
-50 -50 w/50ft per sensor
Cable Termination Options
-PT -PT w/Tinned Wires
-QDP6 -w/Pre-Wire Connector
38476
 
The 38476 is a 16 GB microSD flash-memory card designed for use in harsh conditions often presented by environmental and industrial applications in which customers require higher reliability, endurance, and performance but also seek a cost-effective solution to meet budget-planning requirements.

Other Accessories

HUB-SDM8
 
The HUB-SDM8 is intended for customers who want to connect up to five external SDMs to the same data logger, as well as run multiple power connections using 16 AWG wire. The HUB-SDM8 comprises an environmental enclosure with eight compression fittings (two larger) and eight terminal strips.
L29370
 
One 29370 kit is needed for each CPI network, such as those using a CDM-VW300, CDM-VW305, or SC-CPI. Among the items included in the 29370 kit is a roll of yellow vinyl electrical tape to distinguish Ethernet cables that use CPI protocol from similar cables used for TCP/IP.
L28899
 
The 28899 is a 2 ft CAT6 Ethernet cable used to connect a HUB-CPI to a CPI socket on a dat alogger, or to connect one HUB-CPI to another HUB-CPI.

Replacement Parts

35244
 
The 35244 is a temperature and relative humidity sensor with an R. M. Young Company six-plate radiation shield for use with the CSAT3BH. The 35244 provides critical temperature and relative humidity data to the CSAT3H Controller Box, which is then used to control the heaters within the heated sonic anemometers. Because the 35244 is included with the heated sonic anemometers, it is purchased as a replacement part, rather than as a stand-alone sensor.
41303-5A
 
The 41303-5A is a naturally aspirated, 6-plate radiation shield. Its louvered construction allows air to pass freely through the shield, serving to keep the probe at or near ambient temperature. The shield's white color reflects solar radiation.
35240
 
The CSAT3H Heated Controller is a box with the electronics that control the heaters within the CSAT3BH. The CSAT3H is included with the CSAT3BH; however, it can be purchased separately if a replacement box is needed.
26559
 
The CM250 is a mounting kit for several products that are mounted and leveled on the end of a crossarm. It consists of a fabricated aluminum adapter with set screws, a captive 3/8 in. bolt, and a 3/16 in. Allen wrench. The adapter is meant to be attached to the end of a 1.31 in. outer diameter pipe or crossarm, such as the CM204. The 3/16 in. Allen wrench may be used to tighten the pair set screws that hold the adapter in place on the crossarm. The captive 3/8 in. bolt screws into the block or base of the sensor being mounted. As the bolt is tightened, the base of the sensor and the top of the adapter form a ball-and-socket joint that can be adjusted until the sensor is level.
35634
 
The 35634 is a large, rugged carrying case without foam to accommodate a CSAT3BH and its accessories. Campbell Scientific recommends using this case when when transporting or shipping the CSAT3BH. The 35634 is intended for use with the foam inserts that were originally shipped with the CSAT3BH.
35633
 
The 35633 is a large, rugged carrying case with foam to accommodate a CSAT3BH and its accessories. Campbell Scientific recommends using this case when transporting or shipping the CSAT3BH.