Current Version: 4.4
Short Cut Program Generator (SCWin) is a free, menu-driven, PC-compatible software package that simplifies the creation of data logger programs; it creates a data logger program in seven easy steps.
To download Short Cut, refer to the Downloads section or click the Download Now button.Read More
Originally intended to support meteorological and hydrological applications, the initial releases of Short Cut (SCWin) supported over 120 sensors. Now, with additional program generation capabilities, Short Cut supports programming for our multiplexers, AVW200-series Vibrating Wire Interfaces, ET107 stations, ET106 stations, MetData1 stations, and most sensors that can be measured by our data loggers.
Short Cut allows the user to select sensors and choose output data. Short Cut then creates a wiring diagram and a program file for transfer to the data logger. It also includes support for algebraic entry of expressions.
|Operating System||Windows 11, 10, 8, and 7 (Both 32- and 64-bit operating systems are supported.)|
|Purchased Separately||Free download|
|Communications Supported||N/A (program generator only)|
|Scheduled Data Collection Supported||N/A (program generator only)|
|Data Display Supported||N/A (program generator only)|
Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.
Computer operating systems—Windows 7, 8, 10, and 11. Short Cut runs on both 32-bit and 64-bit versions of these operating systems.
Short Cut supports more than 100 sensors (including generic measurements), multiplexers, AVW200-series vibrating wire interfaces, and the ET107.
Short Cut creates simple programs for our CR200-series, CR300-series, CR510, CR500, CR10(X), 21X, CR23X, CR6, CR800, CR1000(X), CR3000, CR5000, CR9000X and GRANITE dataloggers. Both mixed array and table data operating systems are supported. Short Cut also supports our ET106, ET107 and MetData1 weather stations. The newest version includes the latest sensor files.
Number of FAQs related to Short Cut: 15
Expand AllCollapse All
The SCWin revision history information can be found through the “Software and OS Revision Histories” web page for Short Cut.
No. Short Cut version 3.0 cannot be used to program the data logger to send data via FTP.
The Half Bridge instruction should be selected (not the 3 Wire or 4 Wire options) in Short Cut. The following parameters are data logger specific, but the following can be used on the CR1000 datalogger with the sensor wired to SE1, and Vx1:
|How many HalfBr Sensors?||1|
|Total Bridge Resistance||1000 ohm|
|Excitation Voltage||2500 mV|
|Sensors per excitation channel||1|
|Range of sensor voltage||2500 mV|
50 or 60Hz
|Settling Time||20000 µs|
|Multiplier||Determined during installation (see manual)|
|Offset||Determined during installation (see manual)|
No. Campbell Scientific recommends tracking the battery voltage, program signature, and data logger temperature over time for troubleshooting purposes.
Short Cut does not allow mV readings. To record the raw mV data before it is converted to NTU, open the Short Cut file in the CRBasic Editor, and alter the program manually.
No. A CRBasic or Edlog data logger editor (included in PC400 and LoggerNet software) is needed to write program code for the TDR100. Short Cut for Windows (SCWin) is not designed to handle the many variables of the TDR100.
Yes. In the Water | Level & Flow folder, there is the option to select CS475/CS476/CS477 Radar Water Level Sensor. Click to move the selection to the Selected device window, and enter the SDI-12 address.
It is possible that an older version of Short Cut is being used. Download the latest version of Short Cut.
For programming assistance, consult the NR01-L instruction manual. For additional assistance, contact Campbell Scientific.
Short Cut for Windows (SCWin) ships in all of Campbell Scientific’s support software packages. It is also available as a free download in the Downloads section of the SCWin product page.
SCWin can be used to create programs by going through a simple five-step process. The generated data logger program can be used “as is,” or it can be opened up in the CRBasic Editor (the programming editor that is included with RTDAQ, LoggerNet, and PC400). SCWin provides a good example of programming, as well as a head start on a new program.
Note that any changes made to the CRBasic program cannot be imported back into SCWin.
We do not offer an individual manual for SCWin (Short Cut for Windows). Short Cut information is provided in the LoggerNet, RTDAQ, and PC400 manuals. Information can also be obtained from the Help screens within SCWin.