CR6
 
CR6 Measurement & Control Datalogger
 
Communication Options - show details
-NA -NA No Additional Coms
Comes with the standard communication methods only (CS I/O, USB, CPI, RS-232, Ethernet, etc.).
-WIFI -WIFI w/Wireless Modem
Offers built-in Wi-Fi capability, making it ideal for short-range, wireless IP communications. This option includes one 16005 2.4 GHz 0 dBd Omnidirectional 1/2 Wave Whip Antenna.
-RF407 -RF407 w/900MHz Radio
Offers built-in spread-spectrum radio; ideal for medium-range wireless communication. Designed primarily for operation in the North America. Requires additional antenna.
-RF412 -RF412 w/920MHz Radio
Offers built-in spread-spectrum radio; ideal for medium-range wireless communication. Designed primarily for operation in Australia and New Zealand. Requires additional antenna.
-RF422 -RF422 w/868MHz Radio
Offers built-in radio with listen-before-talk (LBT) and adaptive-frequency-agility (AFA); ideal for medium-range wireless communication. Designed primarily for operation in the EU. Requires additional antenna.
-RF427 -RF427 w/Radio for Brazil
Offers built-in 900 MHz spread-spectrum radio. This model is best suited for applications in Brazil.
-RF451 -RF451 w/1W 900MHz Radio
Offers built-in frequency-hopping spread-spectrum 1W radio; ideal for long-range wireless communication. Designed primarily for operation in the USA, Canada, and Australia. Requires additional antenna.
Temperature Ranges - show details
-ST -ST -40 to +70C
Every CR6 is tested and guaranteed to perform within published specifications over the standard temperature range. Units are tested and shipped to the standard temperature range unless an extended range is specified. Any internal batteries are not tested or guaranteed across the entire standard temperature range.
-XT -XT -55 to +85C
When ordered, the CR6 is tested and guaranteed to perform over the extended temperature range. The extended testing covers the -55° to +85°C range. Any internal batteries or wireless communication modules are not tested or guaranteed across the entire extended temperature range.
Warranty Lengths - show details
-SW -SW Standard 3yr Warranty
At the time of purchase, the CR6 includes a standard warranty of 36 months. See our full warranty policy in the CR6 manual for the terms and conditions of this warranty.
-XW -XW 4yr Warr Extension
Our Extended Warranty adds 48 months to the standard 36 month warranty, bringing the total warranty period to 84 months. The extended warranty may be purchased only at the time of original product purchase. It may NOT be "added later." Except for the increased coverage length, the same terms and conditions apply to the extended warranty as apply to the standard warranty.
Calibration Options - show details
-CC -CC Campbell Calibration
The data logger is calibrated at Campbell Scientific over the selected temperature range
-IC -IC ISO 17025 Calibration
In addition to the Campbell Scientific calibration over the selected temperature range, the data logger calibration is verified by an independent certifying body that is A2LA accredited to the ISO 17025 standards. A paper certificate of the A2LA ISO/IEC 17025 accredited calibration is provided.

Add to your Quote List


Common Accessories

CR1000KD
 
The CR1000KD is a portable keyboard display for viewing and entering data logger data. One CR1000KD may be carried from station to station in a CR6 network. Users can customize menus and displays, simplifying routine operations.
CD100
 
The CD100 can be mounted in an enclosure lid allowing the user to enter and view data without opening the enclosure. It has a vacuum flourescent display for responsive use through a very wide operating temperature range. Users can customize menus and displays, simplifying routine operations
L31055
 
This cable is used to connect a DCE serial device, such as a cellular modem, to the RS-232/CPI port.
L31056
 
This cable is used to connect a DTE serial device, such as a computer or terminal server, to the RS-232/CPI port.
SC110
 
The SC110 consists of two cables, each 0.6 m (2 ft) in length. One cable consists of a 9-pin male connector on one end with stripped and tinned leads on the other for connection to CR6 Control Ports. The other cable is identical except that a 9-pin female connector replaces the male connector. By having two cables, connection of either an RS-232 DCE or DTE device is supported, depending on the cable used.
L29796
 
L29796 Power Supply 24Vdc 1.67A Output, 100-240Vac 1A Input, 5ft Cable
 
The 29796 recharges sealed rechargeable batteries with ac power. This 24 Vdc wall charger can have either a USA/Canada plug or seven international plugs. The cable has a 5 ft length and terminates in pigtails with "+" and "-" labels. See below for available battery packs.
BP12
 
The BP12 is a rechargeable, 12 Vdc, 12 A h battery pack that can power a Campbell Scientific system that has components that have above-average power requirements, such as satellite transmitters.
L27158
 
Campbell Scientific recommends using at least one microSD card with the CR6, and the 27158 is one option. The 27158 is a microSD card for storing the CR6 data.
L27159
 
Campbell Scientific recommends using at least one microSD card with the system, and the 27159 is one option. The 27159 is a 16 GB microSD flash-memory card. This card is designed for use in harsh conditions often presented by environmental and industrial applications. The card uses single-level cell (SLC) memory, which aids in its ability to operate over wide temperature ranges, consume less power, and provide a reliable data-storage medium through more read-write cycles.
L28899
 
Campbell offers two RJ-45 cables that can be used with the CR6's Ethernet and CPI ports. The 28899 is a CAT6 cable with a 0.6 m (2 ft) length.
 
Campbell offers two RJ-45 cables that can be used with the CR6's Ethernet and CPI ports. The 28900 is a CAT5e cable with a 3 m (10 ft) length.
L16755
 
The 16755 is one antenna option for use with Wi-Fi. The 16755 is a high-gain (13 dBd), directional (Yagi) antenna used with our 2.4 GHz radio transceivers. It is intended for longer distances, and for communicating to one other station (due to narrow beam width).
L15730
 
The 15730 is a 900 MHz, unity gain (0 dBd), 1/4 wave whip, right-angle antenna. The 15730 is an omnidirectional antenna that attaches directly to the product (no cables). It should be used inside an enclosure or building.
L14221
 
The 14221 is a 3 dBd omnidirectional antenna for use with many of our spread-spectrum products. The 14221 is suitable for base station use where you need to communicate with multiple stations located in different directions. It is also preferred in mobile applications and in other applications in which the best radio path is not constant, including close-up applications without clear line-of-sight.
L14205
 
The 14205 is a high-gain (6 dBd), directional (Yagi) antenna. It is useful for making RF links over longer distances in one direction. The 14205 requires an antenna cable to connect it to the spread-spectrum transceiver.
COAXRPSMA-L
 
COAXRPSMA-L Antenna Cable LMR195 w/Reverse Polarity SMA & Type N Male Connector
 
The COAXRPSMA-L is an LMR195 coaxial cable fitted with a Type N Male connector on one end and a Reverse Polarity SMA (RPSMA) male connector on the other end. This cable is commonly used to connect an antenna with Type N connector to a spread-spectrum radio with an RPSMA connector.
L31314
 
The 31314 is an RF surge protection kit with flange mounting bracket. It may be flange-mounted to an enclosure backplate or bulkhead-mounted through an enclosure wall. One side of the surge protector connects to a radio with an RPSMA antenna connection. The other side connects to an antenna/antenna coaxial cable with Type N connector.

Other Accessories

L17752
 
The 17752 Reader/Writer allows a computer's USB port to read the data stored on a microSD card.

Replacement Parts

27555
 
The 27555 is a USB Type A to Micro B, male-to-male cable, 6 to 6.5 ft long. It connects devices using the Micro B interface to a USB port on a computer.
L505
 
These screws, along with the 6044 grommets, are commonly used together to secure our equipment to the backplates of our enclosures.
6044
 
These grommets are commonly used with the 505 screws to secure our equipment to the backplates of our enclosures.
L16005
 
The 16005 is shipped with the -WIFI option and is available as a replacement part. The 16005 is a unity gain (0 dBd), 1/2 wave whip, omnidrectional antenna that features an articulating knuckle joint for easy orientation, weatherized jacket for outdoor applications, and internal counterpoise for ground plane independence.